Automotive Oscilloscope Accessories

Page 1 of 1:    15 Items

Automotive Pressure Tester/Diagnostic Kit

Automotive Pressure Tester/Diagnostic Kit£289.00

This diagnostic pressure kit gives you the opportunity to monitor the engine’s dynamic pressure and vacuum and thus access its performance.

Coil on Plug Extension Lead

Coil on Plug Extension Lead£30.00  -  £115.00

Coil on Plug extension lead allows testing of Coil on plug ignition systems, available in single or set of four

Autoditex PPS Pressure Pulse Sensor For oscilloscope

Autoditex PPS Pressure Pulse Sensor For oscilloscope£69.99   £59.99

The Autoditex PPS Pressure Pulse Sensor detects such faults as burnt valves, bad injectors and other performance problems without major disassembly of the engine

600 Ampere AC/DC Current Clamp

600 Ampere AC/DC Current Clamp

The CA-600 amp clamp is a transducer which will allow your oscilloscope, motortester or multimeter to measure electrical current up to 600 amperes, both types AC or DC, with a frequency response up to 400 Hz.

65 Amp AC/DC Current Clamp

65 Amp AC/DC Current Clamp£80.00   £75.00

The CA-60 amp clamp is a transducer which will allow your oscilloscope, motortester or multimeter to measure electrical current up to 60 amperes, both types AC or DC, 

Number 1 Cylinder Trigger Pick-up Clamp BNC fitting

Number 1 Cylinder Trigger Pick-up Clamp BNC fitting£55.99

Clipped on to number 1 cylinder spark plug lead this provides the trigger signal that is used to identify the correct cylinder number of each ignition voltage signal.

Attenuator Passive  10-1 for Automotive Oscilloscope

Attenuator Passive 10-1 for Automotive Oscilloscope£30.00

This is an essential addition for your oscilloscope for measuring higher voltages. Its main purpose is to measure the voltage from the primary ignition system and others.

AC Coupling Adapter for Automotive Oscilloscope

AC Coupling Adapter for Automotive Oscilloscope£30.00

Performs relative engine compression test when attached to oscilloscope

Attenuator Passive  20-1 for Automotive Oscilloscope

Attenuator Passive 20-1 for Automotive Oscilloscope£30.00

This is an essential addition for your oscilloscope for measuring higher voltages. Its main purpose is to measure the voltage from the primary ignition system and others.

AUTOMOTIVE INSULATION PIERCING TEST CLIP - PROBE

AUTOMOTIVE INSULATION PIERCING TEST CLIP - PROBE£30.00

use this quality automotive probe to test components such as fuel injectors or sensors while providing complete insulation to grounding due to its design

Secondary Ignition- HT Capacitive Clamp BNC Type | Scantool Direct

Secondary Ignition- HT Capacitive Clamp BNC Type | Scantool Direct£39.00   £29.99

Used for observing and measuring signals from the secondary ignition system's high-voltage spark plug leads. It can be used with most oscilloscopes

COP- Coil on Plug Pick up sensor to BNC

COP- Coil on Plug Pick up sensor to BNC£38.00   £30.00

The COP sensor can be used as an additional pick-up probe to any automobile oscilloscope

High Speed USB Isolator. USB 2.0 compatible  | Scantool Direct

High Speed USB Isolator. USB 2.0 compatible | Scantool Direct£64.99

USB-to-USB 2.0 compatible High speed isolator protects your PC or Laptop while connecting USB peripherals wired to high voltages.

4mm Banana Backpin  Probes, Automotive  Pins

4mm Banana Backpin Probes, Automotive Pins£19.99

The main application for the probes are for making measurements on the automobile electrical installation without damaging the wire insulation.

Insulated piercing test clips

Insulated piercing test clips£26.99

Pair of fully insulated test probes 


Page 1 of 1:    15 Items

 

TEL: 02891 310 043

E: info@scantool-direct.co.uk