Automotive Oscilloscopes Accessories and tools

 

 
Page 1 of 1:    14 Items

Autoditex PPS Pressure Pulse Sensor For oscilloscope

Autoditex PPS Pressure Pulse Sensor For oscilloscope£77.00

The Autoditex PPS Pressure Pulse Sensor detects such faults as burnt valves, bad injectors and other performance problems without major disassembly of the engine

Attenuator Passive  10-1 for Automotive Oscilloscope

Attenuator Passive 10-1 for Automotive Oscilloscope£39.00

This is an essential addition for your oscilloscope for measuring higher voltages. Its main purpose is to measure the voltage from the primary ignition system and others.

4mm Banana Backpinning  Probes, Automotive Needles

4mm Banana Backpinning Probes, Automotive Needles£19.99

The main application for the probes are for making measurements on the automobile electrical installation without damaging the wire insulation.

600 Ampere AC/DC Current Clamp

600 Ampere AC/DC Current Clamp£130.00

The CA-600 amp clamp is a transducer which will allow your oscilloscope, motortester or multimeter to measure electrical current up to 600 amperes, both types AC or DC, with a frequency response up to 400 Hz.

60 Amp AC/DC Current Clamp

60 Amp AC/DC Current Clamp£115.00

The CA-60 amp clamp is a transducer which will allow your oscilloscope, motortester or multimeter to measure electrical current up to 60 amperes, both types AC or DC, 

AC Coupling Adapter for Automotive Oscilloscope

AC Coupling Adapter for Automotive Oscilloscope£39.00

Performs relative engine compression test when attached to oscilloscope

Attenuator Passive  20-1 for Automotive Oscilloscope

Attenuator Passive 20-1 for Automotive Oscilloscope£39.00

This is an essential addition for your oscilloscope for measuring higher voltages. Its main purpose is to measure the voltage from the primary ignition system and others.

Coil on Plug Extension Lead

Coil on Plug Extension Lead£30.00  -  £115.00

Coil on Plug extension lead allows testing of Coil on plug ignition systems, available in single or set of four

COP- Coil on Plug Pick up sensor to BNC

COP- Coil on Plug Pick up sensor to BNC£38.00   £39.00

The COP sensor can be used as an additional pick-up probe to any automobile oscilloscope

High Speed USB Isolator. USB 2.0 compatible  | Scantool Direct

High Speed USB Isolator. USB 2.0 compatible | Scantool Direct£64.99

USB-to-USB 2.0 compatible High speed isolator protects your PC or Laptop while connecting USB peripherals wired to high voltages.

Number 1 Cylinder Trigger Pick-up Clamp BNC fitting

Number 1 Cylinder Trigger Pick-up Clamp BNC fitting£64.99

Clipped on to number 1 cylinder spark plug lead this provides the trigger signal that is used to identify the correct cylinder number of each ignition voltage signal.

Secondary Ignition- HT Capacitive Clamp BNC Type | Scantool Direct

Secondary Ignition- HT Capacitive Clamp BNC Type | Scantool Direct£39.00   £29.99

Used for observing and measuring signals from the secondary ignition system's high-voltage spark plug leads. It can be used with most oscilloscopes

Automotive Pressure Tester/Diagnostic Kit

Automotive Pressure Tester/Diagnostic Kit£289.00

This diagnostic pressure kit gives you the opportunity to monitor the engine’s dynamic pressure and vacuum and thus access its performance.

Automotive Resistance Substitution Box 0-10 KOHM

Automotive Resistance Substitution Box 0-10 KOHM£99.00

The Ditex Automotive Resistor Sensor Simulator is useful for simulation purposes in automotive repair work, for inspection and testing applications of car resistor type sensors.

 

Page 1 of 1:    14 Items

 

Product Enquiry: Tel 02891 310 043
Product Support Tel 02891 310 044

E: info@scantool-direct.co.uk